View LTW-006DCG-B12_7000276.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

lite-on technology corporation p r o p e r t y o f l i t e - o n o n l y features * package in 12mm tape on 7" diameter reels. * compatible with automatic placement equipment. * compatible with infrared and vapor phase reflow so lder process. * eia std package. * i.c. compatible. * meet green product and pb-free(according to rohs) package dimensions part no. lens color source color ltw-006dcg-5 yellow ingan white notes: 1. all dimensions are in millimeters (inches). 2. tolerance is 0.1 mm (.004") unless otherwise noted. part no. : ltw-006dcg-5 page : 1 of 11 bns-od-c131/a4 anode
lite-on technology corporation p r o p e r t y o f l i t e - o n o n l y absolute maximum ratings at ta=25 parameter ltw-006dcg-5 unit power dissipation 120 mw peak forward current (1/10 duty cycle, 0.1ms pulse width) 100 ma dc forward current 30 ma reverse voltage 5 v operating temperature range -30 to + 85 storage temperature range -40 to + 100 reflow soldering condition 260 for 10 seconds note: operating the led (in an application) under r everse bias condition might result in damage or failure of the component. suggest ir reflow condition : r-reflow soldering profile for lead free soldering (acc. to j-std-020d) part no. : ltw-006dcg-5 page : 2 of 11 bns-od-c131/a4
lite-on technology corporation p r o p e r t y o f l i t e - o n o n l y electrical optical characteristics at ta=25 parameter symbol part no. ltw- min. typ. max. unit test condition luminous intensity iv 006dcg-5 450 750 mcd if = 5ma note 1, 2, 5 viewing angle 2 1/2 006dcg-5 110 deg fig.6 x 0.277 chromaticity coordinates y 006dcg-5 0.255 if = 5ma note 3, 5 fig.1 forward voltage vf 006dcg-5 2.65 3.25 v if = 5ma esd-withstand voltage esd 006dcg-5 200 v hbm note : 1. luminous intensity is measured with a lig ht sensor and filter combination that approximates the cie eye-response curve. 2. iv classification code is marked on each packing bag. 3. the chromaticity coordinates (x, y) is derived f rom the 1931 cie chromaticity diagram. 4. caution in esd: static electricity and surge damages the led. it is recommend to use a wrist band or anti-e2lectrostatic glove when handling the led. al l devices, equipment and machinery must be properly grounded. 5. cas140b is the test standard for the chromaticit y coordinates (x, y) & iv. 6. the chromaticity coordinates (x, y) guarantee sh ould be added +/- 0.007 tolerance. part no. : ltw-006dcg-5 page : 3 of 11 bns-od-c131/a4
lite-on technology corporation p r o p e r t y o f l i t e - o n o n l y bin code list part no. : ltw-006dcg-5 page : 4 of 11 vf spec. table forward voltage (v) at if = 5ma vf bin min. max. v0 2.65 2.75 v1 2.75 2.85 v2 2.85 2.95 v3 2.95 3.05 v4 3.05 3.15 v5 3.15 3.25 v6 tolerance on each forward voltage bin is +/-0.10 vo lt iv spec. table luminous intensity (mcd) at if = 5ma iv bin min. max. s41 450 500 s42 500 550 s51 550 600 s52 600 650 s61 650 700 s62 700 750 s71 750 800 s72 800 850 s81 850 900 s82 900 950 tolerance on each luminous intensity bin is +/- 7%. bns -od-c131/a4
lite-on technology corporation p r o p e r t y o f l i t e - o n o n l y part no. : ltw-006dcg-5 page : 5 of 11 bns-od-c131/a4 color ranks table color bin limits at if = 5ma ranks cie 1931chromaticity coordinates x 0.265 0.27 0.27 0.265 c12 y 0.237 0.245 0.258 0.25 x 0.27 0.275 0.275 0.27 c21 y 0.245 0.253 0.266 0.258 x 0.275 0.28 0.28 0.275 c22 y 0.253 0.261 0.274 0.266 x 0.28 0.285 0.285 0.28 c31 y 0.261 0.269 0.282 0.274 x 0.285 0.29 0.29 0. 285 c32 y 0.269 0.277 0.29 0.282 x 0.265 0.27 0.27 0.265 b12 y 0.224 0.232 0.245 0.237 x 0.27 0.275 0.275 0.27 b21 y 0.232 0.24 0.253 0.245 x 0.275 0.28 0.28 0.275 b22 y 0.24 0.248 0.261 0.253 x 0.28 0.285 0.285 0.28 b31 y 0.248 0.256 0.269 0.261 x 0.285 0.29 0.29 0.285 b32 y 0.256 0.264 0.277 0.269 tolerance on each hue (x, y) bin is +/- 0.007. c. i. e. 1931 chromaticity diagram @5ma 0.210 0.215 0.220 0.225 0.230 0.235 0.240 0.245 0.250 0.255 0.260 0.265 0.270 0.275 0.280 0.285 0.290 0.295 0.300 0.260 0.265 0.270 0.275 0.280 0.285 0.290 0.295 x-coordinate y-coordinate c12 c21 c22 c31 c32 b12 b21 b22 b32 b31
lite-on technology corporation p r o p e r t y o f l i t e - o n o n l y typical electrical / optical characteristics curves (25 c cc c ambient temperature unless otherwise noted) part no. : ltw-006dcg-5 page : 6 of 11 bns-od-c131/a4
lite-on technology corporation p r o p e r t y o f l i t e - o n o n l y user guide cleaning do not use unspecified chemical liquid to clean led they could harm the package. if cleaning is necessary, immerse the led in ethyl alcohol or isopropyl alcohol at normal temperature for less one minute. recommend printed circuit board attachment pad infrared / vapor phase reflow soldering package dimensions of tape note: 1.all dimensions are in millimeters (inches ). part no. : ltw-006dcg-5 page : 7 of 11 bns-od-c131/a4
lite-on technology corporation p r o p e r t y o f l i t e - o n o n l y package dimensions of reel notes: 1. empty component pockets sealed with top cover ta pe. 2. 7 inch reel-2000 pieces per reel. 3. the maximum number of consecutive missing lamps is two. 4. in accordance with eia-481-1-e2 specifications. part no. : ltw-006dcg-5 page : 8 of 11 bns-od-c131/a4
lite-on technology corporation p r o p e r t y o f l i t e - o n o n l y part no. : ltw-006dcg-5 page : 9 of 11 bns-od-c131/a4 cautions 1. application the leds described here are intended to be used for ordinary electronic equipment (such as office equipment, communication equipment and household ap plications).consult liteons sales in advance for information on applications in which exceptiona l reliability is required, particularly when the fa ilure or malfunction of the leds may directly jeopardize life or health (such as in aviation, transportation , traffic control equipment, medical and life support systems and safety devices). 2. storage this product is qualified as moisture sensitive lev el 3 per jedec j-std-020 precaution when handing this moisture sensitive product is important to ens ure the reliability of the product. the package is sealed: the leds should be stored at 30c or less and 90%rh or less. and the leds are limited to use within one year, while the leds is packed in moistu re-proof package with the desiccants inside. the package is opened: the leds should be stored at 30c or less and 60%rh or less. moreover, the leds are limited to solder process within 168hrs. if the humidity indic ator shows the pink color in 10% even higher or exceed the storage limiting time since opened, that we recommended to baking leds at 60c at least 48hrs. to seal the remainder leds return to p ackage, its recommended to be with workable desiccants in original package. 3. cleaning use alcohol-based cleaning solvents such as isoprop yl alcohol to clean the led if necessary. 4. soldering recommended soldering conditions: reflow soldering soldering iron pre-heat pre-heat time peak temperature soldering time 120~150c 120 sec. max. 260c max. 30 sec. max. temperature soldering time 300c max. 3 sec. max. (one time only) 5. drive method an led is a current-operated device. in order to en sure intensity uniformity on multiple leds connected in parallel in an application, it is reco mmended that a current limiting resistor be incorpo rated in the drive circuit, in series with each led as sh own in circuit a below. circuit model a circuit model b led led (a) recommended circuit. (b) the brightness of each led might appear differe nt due to the differences in the i-v characteristic s of those leds.
lite-on technology corporation p r o p e r t y o f l i t e - o n o n l y part no. : ltw-006dcg-5 page : 10 of 11 bns-od-c131/a4 6. esd (electrostatic discharge) static electricity or power surge will damage the l ed. suggestions to prevent esd damage: use of a conductive wrist band or anti-e2lectrostat ic glove when handling these leds. all devices, equipment, and machinery must be prope rly grounded. work tables, storage racks, etc. should be properly grounded. use ion blower to neutralize the static charge whic h might have built up on surface of the leds plastic lens as a result of friction between leds d uring storage and handling. esd-damaged leds will exhibit abnormal characterist ics such as high reverse leakage current, low forward voltage, or no lightup at low currents. to verify for esd damage, check for lightup and vf of the suspect leds at low currents. the vf of good leds should be >2.0v@0.1ma for i ngan product 7.1 reliability test test item test condition reference standard note number of damaged resistance to soldering heat (reflow soldering) tsld=260 , 10sec. jeita ed-4701 300 301 2 times 0/50 solderability (reflow soldering) tsld=245 5 , 3sec. (lead free solder) jeita ed-4701 300 303 1 time over 95% 0/50 thermal shock -30 ~ 85 30min. 30min. jeita ed-4701 300 307 100 cycles 0/50 temperature cycle -40 ~ 25 ~ 100 ~ 25 30min. 5min. 30min. 5min. jeita ed-4701 100 105 100 cycles 0/50 high temperature storage ta=100 jeita ed-4701 200 201 1000 hrs. 0/50 temperature humidity storage ta=60 , rh=90% jeita ed-4701 100 103 1000 hrs. 0/50 low temperature storage ta=-40 jeita ed-4701 200 202 1000 hrs. 0/50 steady state operating life condition 1 ta=25 , if=20ma 1000 hrs. 0/50 steady state operating life condition 2 ta=25 , if=30ma 500 hrs. 0/50 steady state operating life of high temperature ta=85 , if=5ma 1000 hrs. 0/50 steady state operating life of high humidity heat 60 , rh=90% , if=15ma 500 hrs. 0/50 steady state operating life of low temperature ta=-30 , if=20ma 1000 hrs. 0/50
lite-on technology corporation p r o p e r t y o f l i t e - o n o n l y 7.2 criteria for judging the damage criteria for judgment item symbol test conditions min. max. forward voltage vf if=20ma - u.s.l.*) w 1.1 luminous intensity iv if=20ma u.s.l.**) w 0.7 - 8. others the appearance and specifications of the product ma y be modified for improvement without prior notice. 9. suggested checking list training and certification 1. everyone working in a static-safe area is esd- certified? 2. training records kept and re-certification dat es monitored? static-safe workstation & work areas 1. static-safe workstation or work-e2reas have es d signs? 2. all surfaces and objects at all static-safe wo rkstation and within 1 ft measure less than 100v? 3. all ionizer activated, positioned towards the units? 4. each work surface mats grounding is good? personnel grounding 1. every person (including visitors) handling esd s ensitive (esds) items wear wrist strap, heel strap or conductive shoes with conductive flooring? 2. if conductive footwear used, conductive flooring also present where operator stand or walk? 3. garments, hairs or anything closer than 1 ft to esd items measure less than 100v*? 4. every wrist strap or heel strap/conductive shoes checked daily and result recorded for all dls? 5. all wrist strap or heel strap checkers calibrati on up to date? note: *50v for blue led. device handling 1. every esds items identified by eia-471 labels on item or packaging? 2. all esds items completely inside properly closed static-shielding containers when not at static- safe workstation? 3. no static charge generators (e.g. plastics) insi de shielding containers with esds items? 4. all flexible conductive and dissipative package materials inspected before reuse or recycle? others 1. audit result reported to entity esd control coor dinator? 2. corrective action from previous audits completed ? 3. are audit records complete and on file? part no. : ltw-006dcg-5 page : 11 of 11 bns-od-c131/a4

▲Up To Search▲

Price & Availability of LTW-006DCG-B12

	To Download LTW-006DCG-B12 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .